Siemens SIMATIC IPC677E Operating Instructions Manual Download

Page: 51 / 158

Mounting and connecting the device

3.3 Connecting the device

SIMATIC IPC677E
Operating Instructions, 04/2019, A5E45117996-AA

Requirement

●

You have observed the information under "Country-specific information on supply voltage

(Page 46)".

●

The 24 V DC power source must be adapted to the input data of the device

(see Technical specifications (Page 111)).

Procedure

Make sure that the ON/OFF switch is in the position "I" (OFF) to prevent unintentional

startup of the device when it is connected to the 24 V DC power supply.

Switch off the external 24 V DC power supply.

Connect the 24 V DC plug connector to the device.
Observe the correct polarity of the contacts:

①

Protective conductor

②

Ground

③

24 V DC

If necessary, install the enclosed cable grip.

Secure the 24 V DC cable to the cable grip using a cable tie.

Note
Reverse-polarity protection
The 24 V DC power supply is protected against polarity reversal. When you confuse the

24 V DC connecting cables and ground, the device is not damaged but does not switch on.

After the power supply has been connected correctly, the device will again be ready to

operate.

Summary of Contents for SIMATIC IPC677E































































































































































Search results

Summary of Contents for SIMATIC IPC677E

Reviews:

Related manuals for SIMATIC IPC677E

Brands by name

Popular brands

Siemens SIMATIC IPC677E, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC IPC677E

Reviews:

Related manuals for SIMATIC IPC677E

Brands by name

Popular brands