Siemens Sentron 3VA Manual Download | Manualshive

Page: 148 / 492

background image

Applications

3.4 Use of 3VA UL molded case circuit breaker in DC systems

3VA molded case circuit breakers with UL and IEC certification

146

Manual, 01/2019, L1V30435333-01

3.4.5

Recommended circuits for DC systems IEC

GF

Ground-fault monitoring

1)

750 V DC is not a listed voltage according to UL 489

Note
DC 2-pole (all-pole disconnection), grounded system
The grounded pole must always be assigned to the individual conducting path, so that in the

event of a ground fault there are always 2 conducting paths in series in a circuit with 3-pole

molded case circuit breakers, and 3 conducting paths in series in a circuit with 4-pole molded

case circuit breakers.

Note
DC 2-pole (all-pole disconnection), non-grounded system
If there is no possibility of a double ground fault occurring, or if any ground fault that does

occur is dealt with immediately (ground-fault monitoring), 500 V will be the maximum

permissible direct voltage. In a non-grounded system, all poles must be disconnected.

«
...
146
147
148
149
150
...
»

Summary of Contents for Sentron 3VA













































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Sentron 3VA

Brand: Huntron Pages: 7

Brand: CHINT Pages: 8

Brand: Emerson Pages: 12

Brand: LEGRAND Pages: 12

CESTARI Worm Gearbox line

Brand: WEG Pages: 40

Brand: WEG Pages: 88

EPSITRON ECB 787-1668/0106-0054

Brand: WAGO Pages: 4

Cutler-Hammer DS Series

Brand: Eaton Pages: 93

Moeller ZEV-XSW-820

Brand: Eaton Pages: 6

Brand: Eaton Pages: 38

Brand: L&T Electrical & Automation Pages: 135

Brand: CHINT Pages: 10

Brand: Westinghouse Pages: 47

Brand: ABB Pages: 19

Brand: ABB Pages: 9

Brand: ABB Pages: 10

Brand: ABB Pages: 11

Brand: ABB Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands