Siemens Sentron 3VA Manual Download

Page: 353 / 492

Accessories

4.10 MMB300 maintenance mode box

3VA molded case circuit breakers with UL and IEC certification
Manual, 01/2019, L1V30435333-01

351

4.10

MMB300 maintenance mode box

4.10.1

Operating principle of the MMB300 maintenance mode box

The 3VA6 molded case circuit breakers with the electronic trip system ETUs 3-series,

5-series and 8-series can be functionally expanded with an MMB300 maintenance mode

box.
With the MMB300 maintenance mode box, the Dynamic Arc Sentry mode (DAS mode,

chapter Arc energy reduction (Page 81)) of the molded case circuit breaker is activated and

the setting parameters for the instantaneous short circuit current I

and the ground-fault

current I

are set to the lowest setting values of the circuit breaker. This reduces the let-

through energy of the molded case circuit breaker under fault conditions. This results in

improved protection when personnel is in the vicinity of the installation and the installation is

in maintenance mode.
This parameter changeover can occur, for example, through a door contact at the

switchboard or an externally actuated switch. In addition, a signal lamp or horn, for example,

signals when the circuit breaker is in maintenance mode.
A series connection of up to eight 3VA6 molded case circuit breakers with the associated

MMB300 maintenance mode box is possible.

①

LED display

Digital input

②

<SET> button

DO Digital output

Summary of Contents for Sentron 3VA













































































































































































































































































































































































































































































































Search results

Summary of Contents for Sentron 3VA

Reviews:

Related manuals for Sentron 3VA

Brands by name

Popular brands

Siemens Sentron 3VA, Manual

Search results

Summary of Contents for Sentron 3VA

Reviews:

Related manuals for Sentron 3VA

Brands by name

Popular brands