Siemens SCALANCE W786-x Operating Instructions Manual Download

Page: 9 / 68

SCALANCE W786-x
Operating Instructions, 11/2014, A5E03678337-07

Introduction

3.1

Information on the Operating Instructions

Validity of the Operating Instructions

These operating instructions cover the following products:

Article no. of the RoW version Article no. of the US version

SCALANCE W786-1 RJ-45

6GK5 786-1FC00-0AA0

6GK5 786-1FC00-0AB0

SCALANCE W786-2 RJ-45

6GK5 786-2FC00-0AA0

6GK5 786-2FC00-0AB0

SCALANCE W786-2IA RJ-45

6GK5 786-2HC00-0AA0

6GK5 786-2HC00-0AB0

SCALANCE W786-2 SFP

6GK5 786-2FE00-0AA0

6GK5 786-2FE00-0AB0

If information relates to all the named products, the term SCALANCE W786 will be used.
These operating instructions apply to the following software version:

●

SCALANCE W786 with firmware as of version 5.00

Note
These operating instructions do not apply to devices of the SCALANCE W786-2C product

group (use with WLAN controller).

Purpose of the Operating Instructions

Based on the operating instructions, you will be able to install and connect up the

SCALANCE W786 correctly. Configuring the SCALANCE W786 and integration in a WLAN

are not dealt with in this manual.

Documentation on the accompanying CD

You will find detailed information about configuration in the SCALANCE W700 configuration

manuals on the accompanying SIMATIC NET IWLAN CD under the file name:
PH_SCALANCE-W700-WBM_76.pdf and PH_SCALANCE-W700-CLI_76.pdf

Note
Make sure that you read the explanations and instructions in the README.txt file

Summary of Contents for SCALANCE W786-x





































































Search results

Summary of Contents for SCALANCE W786-x

Reviews:

Related manuals for SCALANCE W786-x

Brands by name

Popular brands

Siemens SCALANCE W786-x, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE W786-x

Reviews:

Related manuals for SCALANCE W786-x

Brands by name

Popular brands