Siemens SCALANCE W786-x Operating Instructions Manual Download

Page: 11 / 68

SCALANCE W786-x
Operating Instructions, 11/2014, A5E03678337-07

Description

4.1

Scope of delivery

The following components are supplied with the SCALANCE W786:

●

SCALANCE W786

●

5 caps for the cover screws

●

Depending on the version, up to 8 plugs for sealing the housing

●

Depending on the version, up to 8 strain relief clamps

●

Connector for the 24 VDC power supply

●

SIMATIC NET Industrial Wireless LAN CD

Note
The installation set with the mounting plate for attachment to an S7-300 rail, a 35 mm DIN

rail or a mast does not ship with the product. You can obtain the installation set under the

following order number: 6GK5 798-8ML00-0AB3.

Please check that the consignment you have received is complete. If the consignment is

incomplete, contact your supplier or your local Siemens office.

Summary of Contents for SCALANCE W786-x





































































Search results

Summary of Contents for SCALANCE W786-x

Reviews:

Related manuals for SCALANCE W786-x

Brands by name

Popular brands

Siemens SCALANCE W786-x, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE W786-x

Reviews:

Related manuals for SCALANCE W786-x

Brands by name

Popular brands