Siemens SCALANCE W786-x Operating Instructions Manual Download Page 52

Page: 52 / 68

Connecting up

6.8 Suitable antenna cables and antennas

SCALANCE W786-x

Operating Instructions, 11/2014, A5E03678337-07

The models SCALANCE W786-2IA RJ-45 and SCALANCE W786C-2IA RJ-45 use internal

omni antennas (3/4 dBi at 2.4 GHz or 5 GHz). For the other SCALANCE W786 models, the

following antennas have been approved:

Type

Properties

Order number

ANT792-6MN

Omni antenna, mast/wall mounting, 6 dBi

2.4 GHz, N-Connect female

6GK5 792-6MN00-0AA6

ANT793-6MN

Omni antenna, mast/wall mounting, 5 dBi

5 GHz, N-Connect female

6GK5 793-6MN00-0AA6

ANT792-8DN

Directional antenna, mast/wall mounting,

14 dBi

2.4 GHz, N-Connect female

6GK5 792-8DN00-0AA6

ANT793-8DJ

Directional antenna, mast/wall mounting,

18 dBi

5 GHz, 2 x N-Connect female

6GK5 793-8DJ00-0AA0

ANT793-8DK

Directional antenna, mast/wall mounting,

23 dBi

5 GHz, 2 x N-Connect female

6GK5 793-8DK00-0AA0

ANT793-8DP

Directional antenna, mast/wall mounting,

13 / 13.5 dBi

4.9 GHz and 5 GHz, N-Connect female

6GK5793-8DP00-0AA0

ANT793-6DT

Wide angle antenna (MIMO), mast/wall

mounting, 8 dBi

5 GHz, 3 x QMA connector female

6GK5 793-6DT00-0AA0

ANT795-6DC

Wide angle antenna, mast/

wall mounting, 9 dBi

2.4 GHz and 5 GHz, N-Connect female

6GK5 795-6DC00-0AA0

ANT793-6DG

Wide angle antenna, mast/

wall mounting, 9 dBi

5 GHz, 2 x N-Connect female

6GK5 793-6DG00-0AA0

ANT795-6MN

Omni antenna, mounted on roof/vehicle,

6/8 dBi

2.4 GHz and 5 GHz, N-Connect female

6GK5 795-6MN10-0AA6

ANT795-6MT

Omni antenna (MIMO), mounted on

roof/vehicle/ceiling, 5/7 dBi

2.4 GHz and 5 GHz, 3 x QMA connector

female

6GK5 795-6MT00-0AA0

ANT795-4MC

Omnidirectional antenna, 3/5 dBi, 2.4 GHz

and 5 GHz, IP65, N-Connect male for

direct installation on the device, straight

connector.

6GK5 795-4MC00-0AA3

ANT795-4MD

Omnidirectional antenna, 3/5 dBi, 2.4 GHz

and 5 GHz, IP65, N-Connect male for

direct installation on the device, 90° con-

nector.

6GK5 795-4MD00-0AA3

ANT795-4MA

Omni antenna, directly on the device, 3/5

dBi

2.4 GHz and 5 GHz, IP30, R-SMA con-

nector male for direct mounting on the

device, connector angle adjustable 0° to

180°.

6GK5 795-4MA00-0AA3

Summary of Contents for SCALANCE W786-x





































































Search results

Summary of Contents for SCALANCE W786-x

Reviews:

Siemens SCALANCE W786-x, Operating Instructions Manual, Page: 52 / 68

Search results

Summary of Contents for SCALANCE W786-x

Reviews: