Siemens SCALANCE W786-x Operating Instructions Manual Download | Manualshive

Page: 33 / 68

background image

SCALANCE W786-x
Operating Instructions, 11/2014, A5E03678337-07

33

Connecting up

6

6.1

Lightning protection, power supply and grounding

Notes on lightning protection

WARNING

Danger due to lightning strikes
Antennas installed outdoors must be within the area covered by a lightning protection

system. Make sure that all conducting systems entering from outdoors can be protected by

a lightning protection potential equalization system.
When implementing your lightning protection concept, make sure you adhere to the VDE

0182 or IEC 62305 standard.

Suitable lightning protectors are available in the range of accessories of SIMATIC NET

Industrial WLAN:

●

Lightning protector LP798-1N (order no. 6GK5798-2LP00-2AA6)

●

Lightning protector LP798-2N (order no. 6GK5798-2LP10-2AA6)

Note
We recommend that you use the maintenance-free lightning protector LP798-2N.

Exception:
When there is also DC power is supplied via the antenna cable. In this case, only the

lightning protector LP798-1N can be used.

WARNING

Danger due to lightning strikes
Installing this lightning protector between an antenna and a SCALANCE W700 is not

adequate protection against a lightning strike. The LP798-1N lightening protector only

works within the framework of a comprehensive lightning protection concept. If you have

questions, ask a qualified specialist company.

«
...
31
32
33
34
35
...
»

Summary of Contents for SCALANCE W786-x





































































Reviews:

No comments

Related manuals for SCALANCE W786-x

Brand: Qongle Pages: 13

DGL-4500 - GamerLounge Xtreme N Gaming Router...

Brand: D-Link Pages: 108

DAP-3520 - AirPremier N Dual Band Exterior PoE Access...

Brand: D-Link Pages: 38

DAP-3520 - AirPremier N Dual Band Exterior PoE Access...

Brand: D-Link Pages: 80

DAP-2590 - AirPremier N Dual Band PoE Access...

Brand: D-Link Pages: 36

Brand: Enterasys Pages: 36

Spectrum24 AP-41X1-1050 HR

Brand: Symbol Pages: 2

UHF Wireless Series

Brand: LD Pages: 5

Brand: Z-Com Pages: 23

VERSA WIRELESS LAN - RELEASE NOTES

Brand: NEC Pages: 4

Brand: Ubiquiti Pages: 14

Brand: H3C Pages: 41

LigoPTP 5-23 UNITY

Brand: LogoWave Pages: 14

Brand: 7links Pages: 170

Skyr@cer USB 4101GMR

Brand: Topcom Pages: 212

Brand: Netis Pages: 16

Brand: LevelOne Pages: 31

Brand: TRENDnet Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands