manualshive.com logo in svg

Siemens SCALANCE W786-x, Operating Instructions Manual, Page: 53 / 68

Share
Download
Siemens SCALANCE W786-x Operating Instructions Manual Download Page 53

 

Connecting up 

 

6.9 Connecting external antennas 

SCALANCE W786-x 
Operating Instructions, 11/2014, A5E03678337-07 

53

 

Type 

Properties 

Order number 

ANT792-4DN 

RCoax helical antenna, circular polariza-

tion, 4 dBi, 2.4 GHz, N-connect female. 

6GK5 792-4DN00-0AA6 

ANT793-4MN 

RCoax 

λ

5/8 antenna with vertical polariza-

tion, 6 dBi, 5 GHz, N-connect female. 

6GK5 793-4MN00-0AA6 

IWLAN RCoax cable 2.4 

GHz PE 1/2" 

Omni antenna, 0 dBi 

2.400 - 2.485 GHz, N-Connect female. 

6XV1875-2A 

IWLAN RCoax cable 5 

GHz PE 1/2" 

Omni antenna, 0 dBi 

5.150 - 5.875 GHz, N-Connect female. 

6XV1875-2D 

 
 

 

Note 
ANT793-8DJ 
The antenna ANT793-8DJ may only be used with the antenna cable 6XV1875-5CH50 (5 m 

length) or 6XV1875-5CN10 (10 m length). Other antenna cables are not permitted. 
Notice for USA/Canada 
Only one antenna per device can be used (connected to R1A1, R1A2 or R2A1, R2A2). 

 

 

Note 
ANT793-8DK 
The antenna ANT793-8DK may only be used with the antenna cable 6XV1875-5CN10 (10 m 

length). Other antenna cables are not permitted. 
Notice for USA/Canada 
Only one antenna per device can be used (connected to R1A1, R1A2 or R2A1, R2A2). 

 

6.9

 

Connecting external antennas 

How to connect external antennas 

 

 

Note 

•

 

If both interfaces of access points with two IWLAN interfaces are operated in the same 

frequency range, 

–

 

the distance between the antennas connected to R1A1, R1A2, R1A3 and those 

connected to R2A1, R2A2, R2A3 must be at least 1 m. 

–

 

there may be wireless interference on one or both IWLAN interfaces if the transmit 

power is higher than 15 dB. 

•

 

First, connect the cables to the "R2" sockets if you are using more than one antenna for 

an interface. After connecting the cables to the "R1" sockets, the "R2" sockets are difficult 

to reach. 

 

Summary of Contents for SCALANCE W786-x





































































Reviews:

No comments