manualshive.com logo in svg

Siemens SCALANCE W786-x, Operating Instructions Manual, Page: 36 / 68

Share
Download
Siemens SCALANCE W786-x Operating Instructions Manual Download Page 36

Connecting up 

 

6.1 Lightning protection, power supply and grounding 

 

SCALANCE W786-x 

36

 

Operating Instructions, 11/2014, A5E03678337-07 

 

 

WARNING 

EXPLOSION HAZARD 
SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION 

2 OR ZONE 2. 

 
 

 

WARNING 

EXPLOSION HAZARD 
DO NOT OPEN WHEN ENERGIZED. 

 

General notes on use according to ATEX and IECEx 

 

 

 

WARNING 

Take measures to prevent transient voltage surges of more than 40% of the rated voltage. 

This is the case if you only operate devices with SELV (safety extra-low voltage). 

 

General notes on use in hazardous areas according to UL-HazLoc 

 

 

WARNING 

EXPLOSION HAZARD 
DO NOT DISCONNECT WHILE CIRCUIT IS LIVE UNLESS AREA IS KNOWN TO BE 

NON-HAZARDOUS. 

 

This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D or non-

hazardous locations only. 
This equipment is suitable for use in Class I, Zone 2, Group IIC or non-hazardous locations 

only. 

WARNING - Cat. Nos. EAPN-Wx-yy-zx (US installation only): 

- PLTC cable type and manufacturer shall be specified: Listed (QPTZ), Type 5240U1 

(Waterdog PLTC-ER) manufactured by Belden. 
- The PLTC cable for the power supply must be installed in a manner to avoid tensile stress 

at the termination fittings in accordance with Article 501.10 (B)(1)(4) of the NEC. 
- The PLTC cable for the power supply must be installed in accordance with Article 725.154 

(D)(1) through (D)(4) of the NEC. 

Summary of Contents for SCALANCE W786-x





































































Reviews:

No comments