manualshive.com logo in svg

Siemens SCALANCE W786-x, Operating Instructions Manual, Page: 51 / 68

Share
Download
Siemens SCALANCE W786-x Operating Instructions Manual Download Page 51

 

Connecting up 

 

6.8 Suitable antenna cables and antennas 

SCALANCE W786-x 
Operating Instructions, 11/2014, A5E03678337-07 

51

 

6.8

 

Suitable antenna cables and antennas 

N-Connect/R-SMA connecting cable for RJ-45 

The N-Connect/R-SMA male/male flexible connecting cable is available as an accessory for 

connecting to a SCALANCE W700 with R-SMA connectors. 

 

Length 

Order number 

0.3 m 
1 m 
2 m 
5 m 
10 m 

6XV1875-5CE30 
6XV1875-5CH10 
6XV1875-5CH20 
6XV1875-5CH50 
6XV1875-5CN10 

N-Connect / N-Connect connecting cable for M12 

The N-Connect/N-Connect male/male flexible connecting cable is available as an accessory 

for connecting to a SCALANCE W700 M12 or for connection to the LP798-1N/LP798-2N 

lightning protector. 

 

Length 

Order number 

1 m 
2 m 
5 m 
10 m 

6XV1875-5AH10 
6XV1875-5AH20 
6XV1875-5AH50 
6XV1875-5AN10 

Connecting cable IWLAN QMA/N-Connect male/female 

Flexible adapter cable of antennas with QMA socket for antenna connecting cable. pack of 3 

 

Length 

Order number 

1 m 

6XV1875-5JH10 

Suitable antennas 

 

 

Note 
When you select an antenna, keep in mind the national approvals for your SCALANCE 

W786. 

 

Summary of Contents for SCALANCE W786-x





































































Reviews:

No comments