manualshive.com logo in svg

Siemens SCALANCE W786-x, Operating Instructions Manual, Page: 42 / 68

Share
Download
Siemens SCALANCE W786-x Operating Instructions Manual Download Page 42

Connecting up 

 

6.4 Connecting the power supply 

 

SCALANCE W786-x 

42

 

Operating Instructions, 11/2014, A5E03678337-07 

6.4

 

Connecting the power supply 

Possible power supplies 

You have the following options for the power supply of the SCALANCE W786: 

Direct 24 VDC supply - direct voltage 
A two-pin plug ships with the SCALANCE W786. 

Power supply adapter 12 to 24 VDC - direct voltage 
The power supply adapter Power Supply PS791-2DC is available as an accessory, order 

number: 6GK5 791-2DC00-0AA0 

Power supply adapter 100 to 240 VAC alternating voltage 
The power supply adapter Power Supply PS791-2AC is available as an accessory, order 

number: 6GK5 791-2AC00-0AA0 

Power over Ethernet (PoE) 
With the SCALANCE W786-x RJ-45, power supply using Power over Ethernet (PoE) is also 

possible. The devices support the standards 802.3at Type 1 (IEEE 802.3af) and IEEE 803.at 

Type 2. With SCALANCE W786-2SFP, Power over the Ethernet is not possible in any 

situation. 

●

 

Gigabit Ethernet 
When you connect to gigabit Ethernet, the power supply is a phantom power supply over 

data wires 1, 2, 3 and 6. This corresponds to alternative A according to IEEE 802.3af. 

●

 

Fast Ethernet 
On an 8-wire Fast Ethernet cable, the power is supplied via the free data wires 4, 5, 7 

and 8. This corresponds to alternative B according to IEEE 802.3af. 

 

 

Note 
Disabling the PoE power supply 
Before you pull a plug via which the device is supplied with power using PoE, disable the 

relevant PoE power supply. 

 

 

Note 
No power sourcing equipment (PSE) 
The W786 cannot be used as a PoE power supply for other devices. 

 

Summary of Contents for SCALANCE W786-x





































































Reviews:

No comments