Siemens NK8222 Installation Function & Configuration Commissioning Safety Regulations Download Page 13

Page: 13 / 90

Introduction

What's new

Building Technologies

A6V10062437_a_en

Fire Safety & Security Products

30.06.2013

2.2

What's new

Here is the list of modifications for new functions and software improvements.

Section

Modifications

Front panel [➙ 25]

NK823x vitality green LED: twice blinking if logging

is running.

SD card [➙ 32]

NK823x units are equipped with a 16 GB SD card

for network communication logging.

Kernel update [➙ 63]

Kernel update procedure: checking of available

memory space added.

SNMP monitoring [➙ 64]

SNMP port is closed by default by NK823x firewall.

Diagnostic functions [➙ 69]

Status information for NK823x logging, firewall and

routing added.

Summary of Contents for NK8222



























































































Search results

Summary of Contents for NK8222

Reviews:

Related manuals for NK8222

Brands by name

Popular brands

Siemens NK8222, Installation Function & Configuration Commissioning Safety Regulations

Search results

Summary of Contents for NK8222

Reviews:

Related manuals for NK8222

Brands by name

Popular brands