Siemens NK8222 Installation Function & Configuration Commissioning Safety Regulations Download Page 87

Page: 87 / 90

Maintenance and diagnostics

Correcting communication failures

Building Technologies

A6V10062437_a_en

Fire Safety & Security Products

30.06.2013

Note: The LON Physical address: Subnet 01. Node 02 and the BACnet Logical

Address 1 are reserved for the NK822x itself and must not be used for the Guarto.

Check if the BACnet Logical Address for the management station in the CS6 Guarto

configuration is set to 1 (To be checked with the CS6 tool SWE6 for Guarto in node

CerCom Bus, properties of node Management Station).

Note: If these settings are incorrect, you will have no communication in run-time,

though no error message will be generated.

9.6.5

No fault generated by network failure - MP3.15 and higher

If you do not receive a fault from an NK8000 when a network failure has occurred, or if

there is a long delay before you receive the fault, decrease the Timer for Micro

Interruptions Threshold communication parameter.

Note: Default value is 0 sec.

Summary of Contents for NK8222



























































































Search results

Summary of Contents for NK8222

Reviews:

Related manuals for NK8222

Brands by name

Popular brands

Siemens NK8222, Installation Function & Configuration Commissioning Safety Regulations

Search results

Summary of Contents for NK8222

Reviews:

Related manuals for NK8222

Brands by name

Popular brands