Siemens NK8222 Installation Function & Configuration Commissioning Safety Regulations Download Page 14

Page: 14 / 90

System limits

NS8210 driver system limits

14
Building Technologies

A6V10062437_a_en

Fire Safety & Security Products

30.06.2013

System limits

The following describes the system limits for the NK82xx units and the corresponding

NS82xx drivers for DMS8000 (MM8000 and MK8000) systems. For detailed

information about supported subsystem software versions see the

NK8000 Release

Notes (document n.A6V10062453.)

3.1

NS8210 driver system limits

NS8210 Ethernet Port connections (CMSDL/IP and CEI 79-5)

Currently, there is a limit of 500 NK82xx units per NS8210.

Note: Please contact customer support for configurations above 100 NK82xx.

NS8210 Transport protocols

NS8210 supports the transport protocols CMSDL/IP or CEI 79-5 for communication

with the Ethernet Ports.

Note: The cryptography option is only supported with the CEI 79-5 protocol.

Multiple host configurations are only supported with the CMSDL/IP protocol.

3.2

NS8011 driver system limits

NS8011 Ethernet Port connections (BACnet/IP)

Currently, there is a limit of 64 BACnet/IP connections per Server/FEP Station.

NS8011 Transport protocols

NS8011 supports the BACnet/IP protocol for communication with the NK8225,

NK8232, and NK8235.

Note: Encryption is not supported.

Subsystems supported

Same as interactions, refer to the list [➙ 12].

Summary of Contents for NK8222



























































































Search results

Summary of Contents for NK8222

Reviews:

Related manuals for NK8222

Brands by name

Popular brands

Siemens NK8222, Installation Function & Configuration Commissioning Safety Regulations

Search results

Summary of Contents for NK8222

Reviews:

Related manuals for NK8222

Brands by name

Popular brands