manualshive.com logo in svg

Siemens NK8222, Installation Function & Configuration Commissioning Safety Regulations

Share
Download
Siemens NK8222 Installation Function & Configuration Commissioning Safety Regulations Download Page 25

Structure and functions 

NK823x hardware

4 

25

Building Technologies 

 

A6V10062437_a_en

Fire Safety & Security Products 

 

30.06.2013

 

NK823x Ethernet port unit (NK8235 in this example) 

4.2.1

 

Front panel 

The front panel houses 9 LED’s. 

Left Side LED’s 

The five LED’s on the left side are, from top to bottom: 
Power (LED green)  
Power (hardware – controlled). 
Vital functions (LED green)  
Software vitality: 

   

Blinking (1 flash): core software running. 

   

Blinking (2 flash): core software running and logging function active. 

Tamper (LED bicolour)  
Unit tamper: 

   

Red means tamper alarm (hardware controlled). 

   

Green means tamper disabled (from management station). 

Download (LED red)  
Network diagnostics: 

   

Off: status OK. 

   

Blinking (1 flash): missing identification from NS8xxx. 

   

Blinking (2 flashes): not used. 

   

Blinking (3 flashes): FTP channel open (default mode; for switch settings see 

Internal DIP Switches. 

   

On: critical/hardware fault. 

Diagnostics (LED yellow)  
Internal interface diagnostics: 

 

Off: status OK. 

 

Blinking (fast): booting operating system after restart. 

 

Blinking (1 flash): missing or insufficient license. 

Summary of Contents for NK8222



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands