Siemens NK8222 Installation Function & Configuration Commissioning Safety Regulations Download Page 46

Page: 46 / 90

Hardware installation

NK823x hardware installation

46
Building Technologies

A6V10062437_a_en

Fire Safety & Security Products

30.06.2013

5.3

NK823x hardware installation

Installation

1. Install the NK82xx unit on the DIN rail.
2. Connect subsystems:

– Subsystem lines using the standard RS232 interfaces on COM1 - COM4.

Note: Only COM1 and COM2 are available on NK8231 and NK8232.

– If used in place of COM1, the RS485 interface is on X104.
– If used in place of COM2, the RS485 interface is on X105.

3.  If used, connect the power supply supervision module DF8090.
4.  If used, connect the onboard I/O signals.
5.  Connect power supply.

See Figure

Power connections if using a DF8090 power supply supervision

module.

WARNING

Do not connect or disconnect any device when the device is powered on!

Top view

Back

NK823x electrical interfaces (top view)

Item

Name

Description

USB

Ethernet 2

Ethernet 1

X101

1 output

X102

3 inputs

Summary of Contents for NK8222



























































































Search results

Summary of Contents for NK8222

Reviews:

Related manuals for NK8222

Brands by name

Popular brands

Siemens NK8222, Installation Function & Configuration Commissioning Safety Regulations

Search results

Summary of Contents for NK8222

Reviews:

Related manuals for NK8222

Brands by name

Popular brands