Siemens NK8222 Installation Function & Configuration Commissioning Safety Regulations Download Page 24

Page: 24 / 90

Structure and functions

NK823x hardware

24
Building Technologies

A6V10062437_a_en

Fire Safety & Security Products

30.06.2013

DF8090 Power Supply Supervision

DF8090 is a module designed for monitoring a 12V DC power supply. It can detect the

conditions listed below, shown on the DF8090 local panel and report them to NK822x,

and in turn to management station (see the following):



Mains failure (no 220VAC)



Battery low



Power supply failure (trouble with AC/DC converter)



Battery protection fuse blown (internal micro-fuse type MSF 3.15A/250V)

MAINS

AC/DC

LOW BATT

BATT FUSE

DF8090 front panel

Item

Description

LEDs.

C connector to I/O modules.

See figure

NK822x power connections (see NK822x hardware installation [➙ 37]) for

the NK822x power connections using the power supervision module.
For more information about the DF8000 Input/Output modules, including installation

details, see documents

DF8000 Datasheet (document no.A6V10081184) and DF8000

ICC (document no.A6V10081388)

4.2

NK823x hardware

The NK823x is composed of an electronic board (with optional plug-ins) installed in a

compact and robust plastic box.

Note: NK823x units with build state up to 04 are equipped with the NKM8001-A1

mainboard that do not support locally connected DF8000 I/O modules.

Instead, NK823x units with build state 10 or higher are equipped with the NKM8001-

A2 mainboard that can support up to 4 locally connected I/O modules.

Summary of Contents for NK8222



























































































Search results

Summary of Contents for NK8222

Reviews:

Related manuals for NK8222

Brands by name

Popular brands

Siemens NK8222, Installation Function & Configuration Commissioning Safety Regulations

Search results

Summary of Contents for NK8222

Reviews:

Related manuals for NK8222

Brands by name

Popular brands