manualshive.com logo in svg

Siemens ELP 319, Operating And Service Manual

Share
Download
Siemens ELP 319 Operating And Service Manual Download Page 29

 

 

Industry Mobility 

 

Betriebsanleitung 

PZENTW 

A6Z08101637795/EN1/000/B 

29 

[7620] ELP 319 

LANGE_THO 

 

A25000-X22-Q9-7-7620 

of 

DC013 

20081022 

 

Notice no.: 500000097465 

33 

Copyright (C) Siemens AG  1998 

All Rights Reserved -    

0000ZQ6U.doc

 

 

12.3   Intervals 

Inspection / maintenance jobs 

Interval: 6 months 

Clean and grease detector slides 

Oil connecting bolts 

Refill grease chambers in the guide sleeve from the side of the gasket 

Saturate felt rings at the bearing surfaces of the rockers with oil 

Check proper breaking and making of switching contacts in both end positions 

For 60 V systems, the DC voltage at terminals 3 and 4 must be greater than or equal to 35 V. 

Point machine and end position detector mounted on the same side: 
- 

With the points in the rightmost position (end position detector mounted on the left 

side of points), the resistance between wires 2 and 4 must be below 1.0 Ω. 

 

- 

With the points in the leftmost position (end position detector mounted on the left side of points), the 

resistance between wires 1 and 4 must be below 1.0 Ω. 

Point machine and end position detector mounted opposite each other:

 

- 

With the points in the rightmost position, the resistance between wires 1 and 4 must be below 1.0 Ω.

 

 

- 

With the points in the leftmost position, the resistance between wires 2 and 4 must be below 1.0 Ω. 

Inspection / maintenance jobs 

Interval: 12 months 

Check type label is still in place and clean it 

Check fastening bolts of end position detector and base plates and re-tighten them 

Check, clean and grease detector rods 

Check and grease visible threads of outside fastening bolts 

Check easy movement of cover lock and grease it 

Check end position detector is tight and dry inside, clean and dry it inside 

Check cable gland, connecting cable and protective hose and re-tighten fastening screws 

Check condition of internal wiring 

Check connecting wires are held firmly in the terminal strip 

Re-tighten clamping screws of terminal strip, if necessary 

Check earthing 

Check, clean and grease bolts of detector rods 

Check locking of bolts 

Check lock nuts of adjustable detector rods are tight 

Check fastening and locking elements (bolts, nuts) are tight 

Check cover of detector rods 

Check fastening of detector rod guide is tight 

Check whether any visible parts are damaged or worn out 

Check coat of paint and corrosion protection 

Summary of Contents for ELP 319


































Reviews:

No comments

Brands by name

Popular brands

Load more brands