manualshive.com logo in svg

Siemens ELP 319, Operating And Service Manual

Share
Download
Siemens ELP 319 Operating And Service Manual Download Page 11

 

 

Industry Mobility 

 

Betriebsanleitung 

PZENTW 

A6Z08101637795/EN1/000/B 

11 

[7620] ELP 319 

LANGE_THO 

 

A25000-X22-Q9-7-7620 

of 

DC013 

20081022 

 

Notice no.: 500000097465 

33 

Copyright (C) Siemens AG  1998 

All Rights Reserved -    

0000ZQ6U.doc

 

 

8.1.1   Housing 

The cast-iron housing 1 (see Figure 2) has been designed for maximum reduction of condensation. 
The reduction in size of base which is near to the ground and the enlargement of sides allow a better 
compensation of temperature between equipment and environment. Ventilation openings 10 located 
opposite each other ensure a good circulation of air. 
The housing has a tread-proof aluminium cover 12 with a well-sealing gasket. By turning tension 
screw 17, the gasket is compressed. The pressure can be adjusted by means of adjusting screw 11. 

8.1.2   Detector Slides 

The detector slides 9 (see Figure 2), made of drawn steel, have a carrier 15, a stop pin 21 and 
insulated fork heads 8 for linking the detector rods. The detector slides are supported by guide sleeve 
6 and a cast stalk of the housing. By means of these standard detector slides, together with movable 
contact arrangement 2, point openings from 30 mm to 190 mm can be detected. The travel of the 
open point blade resulting from the locking stroke must not exceed 70 mm until carrier 15 reaches the 
slide of the closed point blade. The carrier travel is so dimensioned that a broken detector rod is 
indicated as soon as the slide stroke exceeds the travel resulting from the locking stroke by at least 
10 mm. This applies even to slide strokes below 80 mm if a correspondingly dimensioned spacer 
block is placed in the slot for the carrier (see also Figure 3). 

Summary of Contents for ELP 319


































Reviews:

No comments

Brands by name

Popular brands

Load more brands