Siemens 7MB2041 Operating Instructions Manual Download Page 58 | Manualshive

Page: 58 / 152

Siemens 7MB2041 Operating Instructions Manual Download Page 58

Operation

5.4 Operating functions

OXYMAT 64

56

Operating Instructions, 06/2008, A5E00880383-03

Single calibration is only possible if the

"Total calibration" subfunction has been deactivated

in function 23.
All measuring ranges defined using function 41 appear in the display. The above function

screen is an example of the single calibration of four measuring ranges.
If you would like to calibrate range 3, press the corresponding softkey.
The setpoint and current actual value of the selected range then appear in the display:

21 Sp.cal. MR 3 O

2

Setpoint : 9999.00 vpm

Act.val. : 9901.00 vpm

Start calibration

CANCEL

Figure 5-11 Calibrate measuring range

When the actual value has stabilized, you can initiate the calibration process by pressing the

fourth softkey. The actual value is now made to agree with the setpoint.
If a calibration is carried out incorrectly (e.g. using the wrong calibration gas) repeat the

complete calibration procedure.
If the calibration is aborted because the calibration tolerance is too large, check your

calibration gas as well as for leaks in the analyzer (chapter 4.3.2). If the calibration gas is

OK, and if there are no leaks, try to carry out a basic calibration using function 26 (adjust

sensor). If the calibration tolerance is still too high, the sensor may be faulty.

Total calibration ("Measure" operating state required)

Total calibration is only possible if the

"Total calibration" subfunction has been activated

using function 23.
With a total calibration, you calibrate all measuring ranges together. Define the "leading"

measuring range in function 22. We recommend that you use the largest measuring range

for this.
The setpoint and current actual value of the "leading" measuring range appear in the display.
When the actual value has stabilized, you can initiate the calibration process by pressing the

fourth softkey. The actual value is now made to agree with the setpoint.
If a calibration is carried out incorrectly (e.g. using the wrong calibration gas) repeat the

complete calibration procedure.

«
...
56
57
58
59
60
...
»

Summary of Contents for 7MB2041

























































































































































Reviews:

No comments