Siemens 7MB2041 Operating Instructions Manual Download Page 112

Page: 112 / 152

Repair, maintenance and servicing

6.6 Removing faults

OXYMAT 64

110

Operating Instructions, 06/2008, A5E00880383-03

6.6.2

Maintenance requests

If there are indications of changes in internal device parameters, "Maintenance request"

appears in the status line. Such changes do not significantly affect the measuring quality at

the time they occur. In order to still guarantee the measuring quality, it may be necessary to

carry out remedial measures.
The following fault messages entail a maintenance request (output in the display) and are

signaled externally if a corresponding relay has been configured using function 71.

Table 6- 2

Causes of maintenance requests

No.

Signal

Possible cause

Remedy

Calibration gas was changed

Calibration tolerance

exceeded

Incorrect setpoint entered

Repeat calibration

Set clock

The device was switched off New input of date and time

Temperature of LC display

too high or too low

Ambient temperature above

45 °C or below 5 °C

Make sure that the ambient

temperature is in the range

from 5 °C to 45 °C.

External maintenance

request

External signal

Check (function 72 must be

configured accordingly)

W10

Autocal check deviation

Violation of the tolerance

was determined during an

"Autocal check"

Summary of Contents for 7MB2041

























































































































































Search results

Summary of Contents for 7MB2041

Reviews:

Siemens 7MB2041, Operating Instructions Manual, Page: 112 / 152

Search results

Summary of Contents for 7MB2041

Reviews: