manualshive.com logo in svg

Siemens 7MB2041, Operating Instructions Manual, Page: 51 / 152

Share
Download
Siemens 7MB2041 Operating Instructions Manual Download Page 51

 

Operation 

 

5.3 Menu control 

OXYMAT 64 
Operating Instructions, 06/2008, A5E00880383-03 

49

 

Some of these are protected against unauthorized access by various level codes. 

 

Menu 

Code level 

Analyzer status 

Not coded 

Calibration 

Code level 1 

Measuring ranges 

Code level 1 

Parameter 

Code level 1 

Configuration 

Code level 2 

The code of level 1 is preset to "111" in the factory, and the code of level 2 is preset to "222". 

Entering a submenu 

If you select a submenu by pressing the associated softkey, the code of the corresponding 

operation level is queried once (exception: the submenu "Analyzer status" is freely 

accessible; selecting this does not change the operating mode). 
Decoding level 2 also decodes level 1.  
By entering a corresponding code, the device switches to the operator control mode, 

whereby the functional check is activated. 
The functional check "CTRL" (shown in the status line of the measured value display) is 

always activated by the device when an intervention endangers correct measurement, e.g. 

when the code is entered. If you have configured a corresponding relay using function 71 

with "Functional check", an extra signal is sent out via the relay contact together with the 

decoding. This relay contact then signals every functional check activation, e.g. even the 

warm-up phases and calibration states of the device. 
Decoding also activates the measured value memory, providing you have parameterized it 

using function 77. The coding status of the device can be read in the status line of the 

measured value display as a symbol "■ CODE" for "coded" or "□ CODE" for "decoded". 

Summary of Contents for 7MB2041

























































































































































Reviews:

No comments