manualshive.com logo in svg

Siemens 6GK5748-1GY01-0AA0, Operating Instructions Manual, Page: 46 / 91

Share
Download
Siemens 6GK5748-1GY01-0AA0 Operating Instructions Manual Download Page 46

Installation and removal 

 

5.3 Wall mounting 

 

SCALANCE W1788-x / W1748-1 

46

 

Operating Instructions, 03/2022, C79000-G8976-C484-05 

2.

 

Prepare the four drill holes for wall mounting. For the precise dimensions, refer to the 

section "Dimension drawings (Page 87)". 
Secure the mounting plate to the wall with four screws 

. Note the direction of the 

holding plate ("TOP").  

 

 

 

Note 

Depending on the mounting surface, use suitable fittings. 

 

 

 

Note 
The holding plate must be securely fastened 

If the holding plate is not securely fastened, the holding plate may fall with the device. 
The mounting material must be capable of supporting at least four times the weight 

of the device and the holding plate. 

 

 

The mounting plate has four key-hole brackets for hanging up the device. The 

mounting material for securing to the base is not supplied with the product; see 

Accessories. (Page 24)  

Summary of Contents for 6GK5748-1GY01-0AA0




























































































Reviews:

No comments