manualshive.com logo in svg

Siemens 6GK5748-1GY01-0AA0, Operating Instructions Manual, Page: 34 / 91

Share
Download
Siemens 6GK5748-1GY01-0AA0 Operating Instructions Manual Download Page 34

Description of the device 

 

4.5 LED display 

 

SCALANCE W1788-x / W1748-1 

34

 

Operating Instructions, 03/2022, C79000-G8976-C484-05 

 

LED 

Color 

Meaning 

L1 
 

Off 

 

Power supply L1 too low. 

Green 

 

Power supply L1 is applied. 

L2 
 

Off 

 

Power supply L2 too low. 

Green 

 

Power supply L2 is applied. 

PoE 

Off 

 

The device is not supplied using PoE. 

Green 

 

The device is supplied using PoE. 

P1 

Off 

 

There is no connection over the Ethernet port P1. 

Green 

 

There is a connection over the Ethernet port P1 (link). 

Flashing green and 

yellow 

 

Data transfer over the Ethernet interface P1. 

Flashing green 

 

 Interval:  

170 ms on / 170 ms off 

The port has the status "Discarding" in the spanning tree. The 

port is part of a spanning tree, however it is located on a 

redundant path and is blocked for data traffic. 

P2 

Off 

 

There is no connection over the Ethernet port P2. 

Green 

 

There is a connection over the Ethernet port P2 (link). 

Flashing green and 

yellow 

 

Data transfer over the Ethernet interface P2. 

Flashing green 

 

Interval:  

170 ms on /  

170 ms off 

The port has the status "Discarding" in the spanning tree. The 

port is part of a spanning tree, however it is located on a 

redundant path and is blocked for data traffic. 

Summary of Contents for 6GK5748-1GY01-0AA0




























































































Reviews:

No comments