manualshive.com logo in svg

Siemens 6GK5748-1GY01-0AA0, Operating Instructions Manual, Page: 32 / 91

Share
Download
Siemens 6GK5748-1GY01-0AA0 Operating Instructions Manual Download Page 32

Description of the device 

 

4.5 LED display 

 

SCALANCE W1788-x / W1748-1 

32

 

Operating Instructions, 03/2022, C79000-G8976-C484-05 

LED 

Color 

Meaning 

Flashing green and 

yellow 

 

Data transfer via the WLAN interface 1. 

Flashing yellow  

 

Interval:  

100 ms on / 100 ms 

off 

Access point mode:

 

With DFS (802.11h), the channel is scanned for one minute for 

competing radar signals before the channel can be used for data 

traffic. 

F 

Off 

 

No fault/error. 

Red 

 

The device is starting up or an error has occurred. 

Flashing red  

 

Interval: 

500 ms on / 500 ms 

off 

The bootloader waits in this state for a new firmware file that you 

can download by TFTP. 

Flashing red  

 

Interval: 

2000 ms on / 

200 ms off 

Firmware on PLUG: 
The device is performing a firmware update or downgrade. 

Red 

 

Simultaneous 

R1 yellow flashing 

 

A competing radar signal was found on all enabled channels. 

P1 

P2 

R1 

Flashing green 

 

The port LEDs flash for detection of device location. 
The "LED flash" function is activated 
•

 

Either with SINEC PNI 

•

 

Or via the WBM page "Discovery and Set via DCP" 

 

Summary of Contents for 6GK5748-1GY01-0AA0




























































































Reviews:

No comments