manualshive.com logo in svg

Siemens 6GK5748-1GY01-0AA0, Operating Instructions Manual, Page: 60 / 91

Share
Download
Siemens 6GK5748-1GY01-0AA0 Operating Instructions Manual Download Page 60

Connection 

 

6.1 Safety when connecting up 

 

SCALANCE W1788-x / W1748-1 

60

 

Operating Instructions, 03/2022, C79000-G8976-C484-05 

 

 

WARNING 

Lack of equipotential bonding 

If there is no equipotential bonding in hazardous areas, there is a risk of explosion due 

to equalizing current or ignition sparks. 
•

 

Ensure that equipotential bonding is available for the device. 

 
 

 

WARNING 

Unprotected cable ends 

There is a risk of explosion due to unprotected cable ends in hazardous areas. 
•

 

Protect unused cable ends according to IEC/EN 60079-14. 

 
 

 

WARNING 

Improper installation of shielded cables 

There is a risk of explosion due to equalizing currents between the hazardous area and 

the non-hazardous area. 
•

 

Ground shielded cables that cross hazardous areas at one end only. 

•

 

Lay a potential equalization conductor when grounding at both ends. 

 
 

 

WARNING 

Insufficient isolation of intrinsically safe and non-intrinsically safe circuits 

Risk of explosion in hazardous areas 
•

 

When connecting intrinsically safe and non-intrinsically safe circuits, ensure that the 

galvanic isolation is performed properly in compliance with local regulations (e.g. IEC 

60079-14). 

•

 

Observe the device approvals applicable for your country. 

 

Summary of Contents for 6GK5748-1GY01-0AA0




























































































Reviews:

No comments