manualshive.com logo in svg

Siemens 6GK5748-1GY01-0AA0, Operating Instructions Manual, Page: 72 / 91

Share
Download
Siemens 6GK5748-1GY01-0AA0 Operating Instructions Manual Download Page 72

Connection 

 

6.6 Replacing a CLP 

 

SCALANCE W1788-x / W1748-1 

72

 

Operating Instructions, 03/2022, C79000-G8976-C484-05 

6.6

 

Replacing a CLP 

Position 

The PLUG slot is on the bottom of the device housing under a cover, see Reset button 

(Page 19). 

 

①

 

CLP 

②

 

Slot cover 

③

 

M3 screws (Torx T10) 

Removing a CLP 

 

 

Note 
Loss of the configuration 

The reset button is located directly beside the slot for the CLP. The reset button cannot 

be used to remove the CLP. 
If you press and hold down the reset button you reset all the settings of the device to the 

factory defaults. 

 

To remove a CLP from the device, follow the steps below: 
1.

 

Turn off the power to the device. 

2.

 

Loosen the screws M3 

③

 with a Torx screwdriver T10 and remove the slot cover 

②

. 

As an alternative, you can loosen only one of the screws 

③

 and swivel the slot cover 

②

 to the side. 

Summary of Contents for 6GK5748-1GY01-0AA0




























































































Reviews:

No comments