manualshive.com logo in svg

Siemens 6GK5748-1GY01-0AA0, Operating Instructions Manual, Page: 5 / 91

Share
Download
Siemens 6GK5748-1GY01-0AA0 Operating Instructions Manual Download Page 5

 

SCALANCE W1788-x / W1748-1 
Operating Instructions, 03/2022, C79000-G8976-C484-05 

5

 

Introduction

 

1 

 

Validity of the Operating Instructions 

These operating instructions cover the following products: 

 

 

Certification ID 

Article number 

Access points

 

SCALANCE W1788-1 M12 

RAPAC-W1-M12-E4 

6GK5788-1GY01-0AA0 

SCALANCE W1788-2 M12 

RAPAC-W2-M12-E4 

6GK5788-2GY01-0AA0 

SCALANCE W1788-2 M12 EEC 

RAPAC-W2-M12-E4 

6GK5788-2GY01-0TA0 

SCALANCE W1788-2IA M12 

RAPAC-W2-M12-I4 

6GK5788-2HY01-0AA0 

Client

 

SCALANCE W1748-1 M12 

RAPAC-W1-M12-E4 

6GK5748-1GY01-0AA0 

These operating instructions apply to the following software version: 
•

 

SCALANCE W1700 with firmware version 3.0 

Definition 

An access point is a node in a WLAN that also performs administrative functions in the 

network and, for example, provides client modules with a connection to wired networks, 

to other client modules in the same wireless cell or in other wireless cells. 

Purpose of the Operating Instructions 

Using the Operating Instructions, you will be able to install and connect the SCALANCE 

W1788/W1748 correctly. The configuration and the integration of the device in a WLAN 

are not described in these instructions. 

Documentation on the Internet 

You can find the current version of the document on the Internet at 

(

https://support.industry.siemens.com/cs/de/en/ps/15859/man

) 

Enter the name or article number of the product in the search filter. 

Documentation on configuration 

You will find detailed information on configuring the devices in the following 

configuration manuals: 
•

 

SCALANCE W1780/W1740 nach IEEE 802.11ac Web Based Management 

•

 

SCALANCE W1780/W1740 nach IEEE 802.11ac Command Line Interface 

Summary of Contents for 6GK5748-1GY01-0AA0




























































































Reviews:

No comments