manualshive.com logo in svg

Siemens 6GK5748-1GY01-0AA0, Operating Instructions Manual, Page: 26 / 91

Share
Download
Siemens 6GK5748-1GY01-0AA0 Operating Instructions Manual Download Page 26

Description of the device 

 

4.4 Accessories 

 

SCALANCE W1788-x / W1748-1 

26

 

Operating Instructions, 03/2022, C79000-G8976-C484-05 

4.4.4

 

Power supply 

Energy cable 

 

Component 

Description 

Article number 

Energy cable 2 

x 0.75 

Energy cable for connection of signaling contact and 

power supply 24 VDC, stranded wire 2 x 0.75 mm

2

, 

trailing type, not assembled 
Sold by the meter 

6XV1812-8A 

Robust Energy 

Cable 4 x 0.75 

Energy cable for connection of power supply 24 

VDC, 4-wire stranded 4 x 0.75 mm

2

, robust, flexible, 

not assembled 
Sold by the meter 

6XV1801-2A 

M12 PLUG-IN 

CABLE 

Flexible plug-in power cable to connect the power 

supply 24 VDC, 4-wire, preassembled with a 4-pin 

M12 plug and an M12 socket (A-coded) 

6XV1801-5D* 

 * Available in different lengths 

Socket 

 

Component 

Description 

Article number 

IE POWER 

M12 CABLE 

CONNECTOR 

PRO 

Socket for the 24 VDC power 

supply. 4-pin, A-coded 

pack of 3 

6GK1907-0DC10-6AA3 

4.4.5

 

Flexible connecting cables, antennas and accessories 

You will find an overview of the IWLAN products and their accessories in the Order 

overview (

https://support.industry.siemens.com/cs/ww/en/view/109766333

). 

4.4.5.1

 

Flexible connecting cables 

Flexible connecting cable N-Connect/R-SMA 

Flexible connecting cable for connecting an antenna to a SCALANCE W device with R-

SMA connectors, preassembled with an N-Connect male and an R-SMA male connector: 

 

Length 

Article number 

0.3 m 

6XV1875-5CE30 

1 m 

6XV1875-5CH10 

2 m 

6XV1875-5CH20 

5 m 

6XV1875-5CH50 

10 m 

6XV1875-5CN10 

Summary of Contents for 6GK5748-1GY01-0AA0




























































































Reviews:

No comments