manualshive.com logo in svg

Siemens 6GK5748-1GY01-0AA0, Operating Instructions Manual, Page: 85 / 91

Share
Download
Siemens 6GK5748-1GY01-0AA0 Operating Instructions Manual Download Page 85

 

Technical specifications 

 

9.2 SCALANCE W1788-2 / W1788-2IA 

SCALANCE W1788-x / W1748-1 
Operating Instructions, 03/2022, C79000-G8976-C484-05 

85

 

Technical specifications 
Permitted ambient conditions

 

Ambient temperature 

During operation   Non EEC variant  -20 

℃

 to +70 

℃

 

EEC variant 

-40 °C ...+75 °C 

During storage 

-40 

℃

 to +85 

℃

 

During transportation 

-40 

℃

 to +85 

℃

 

Relative humidity 

During operation 

≤

 90% at 25 °C, no condensation 

Operating altitude 

During operation 

≤

 2,000 m above sea level at max. 70 °C 

/ 75 °C (EEC) ambient temperature 

Contaminant concentration 

According to ISA-S71.04.-2013 Class G3 

Degree of pollution 

2 

Degree of protection 

IP65 (according to DIN EN 60529) 

Dimensions and weight

 

Dimensions 

W x H x D 

258 x 258 x 80 mm 

Weight 

 2.7 kg 

Installation options

 

Direct 

Wall mounting with mounting plate 

With additional holding plate 

Mounting on a DIN rail with pre-installed DIN rail mounting adapter 
Mounting on the standard rail S7-1200 / S7-1500 with rail mounting adapter 

Mean time between failure (MTBF)

 

 

at 40 °C ambient temperature 

18 years 

Summary of Contents for 6GK5748-1GY01-0AA0




























































































Reviews:

No comments