manualshive.com logo in svg

Siemens 6GK5748-1GY01-0AA0, Operating Instructions Manual, Page: 83 / 91

Share
Download
Siemens 6GK5748-1GY01-0AA0 Operating Instructions Manual Download Page 83

 

Technical specifications 

 

9.2 SCALANCE W1788-2 / W1788-2IA 

SCALANCE W1788-x / W1748-1 
Operating Instructions, 03/2022, C79000-G8976-C484-05 

83

 

Technical specifications 
Mean time between failure (MTBF)

 

 

at 40 °C ambient temperature 

18 years 

9.2

 

SCALANCE W1788-2 / W1788-2IA 

 

 

Note 

You will find detailed information on the transmit power and receiver sensitivity in the 

document "Performance data 802.11ac SCALANCE W1700" on the Internet at 

(

https://support.industry.siemens.com/cs/de/en/view/109759606

). 

 

•

 

SCALANCE W1788-2 M12 

•

 

SCALANCE W1788-2 M12 EEC 

•

 

SCALANCE W1788-2IA M12 

 

Technical specifications 
Data transfer

 

Ethernet transfer rate 

10 / 100 / 1000 Mbps 

Wireless transmission rate 

1 ... 1733 Mbps 

Wireless standards supported 

IEEE 802.11a 
IEEE 802.11b 
IEEE 802.11g 
IEEE 802.11n 
IEEE 802.11ac 

Power supply for PoE standards 

supported 

Standards 

IEEE 802.3at Type 2 

Class 

Class 4 (12.95 

–

 25.50 W) 

Mode 

Mode A, Mode B 

Attachment to Industrial Ethernet

 

 

Quantity 

2 

Design 

M12 socket  

Properties 

Half duplex/full duplex, autocrossover, 

autonegotiation, autosensing, floating, 

PoE at port 2 

Summary of Contents for 6GK5748-1GY01-0AA0




























































































Reviews:

No comments