manualshive.com logo in svg

Siemens 6GK5748-1GY01-0AA0, Operating Instructions Manual, Page: 24 / 91

Share
Download
Siemens 6GK5748-1GY01-0AA0 Operating Instructions Manual Download Page 24

Description of the device 
4.4 Accessories 

SCALANCE W1788-x / W1748-1 

24

Operating Instructions, 03/2022, C79000-G8976-C484-05 

4.4

 

Accessories 

Technical data subject to change. 
You will find further information on the range of accessories in the Industry Mall 

(

https://mall.industry.siemens.com/mall/en/WW/Catalog/Products/10021486

) 

Use the TIA Selection Tool (

https://mall.industry.siemens.com/tst/

) for configuring the 

device. 

4.4.1

 

Installation 

Component 

Description 

Article number 

Installation kit for 

installation on a mounting 

rail 

Bracket set for securing the device on a 

standard rail 
• S7-300 standard rail
• S7-1500 standard rail
Mounting adapter with fixing screws

6GK5798-8MS00-0AA0 

Wall mounting set 

Installation kit for mounting the device to 

the wall or ceiling; mounting plate, fixing 

and locking screws 

6GK5798-8MW00-0AA0 

4.4.2

 

CLP 

4.4.3

 

Industrial Internet 

You will find information on the cabling for communication networks in the industry on 

the Internet pages of Siemens Industry Online Support 

(

https://support.industry.siemens.com/cs/ww/en/view/109766358

). 

Component

Description

Article number

CLP
Configuration License PLUG

Exchangeable storage medium for saving 
configuration data
SCALANCE CLP 2GB

6GK1900-0UB00-0AA0

SCALANCE CLP EEC 2GB

6GK1900-0UQ00-0AA0

CLP iFeatures

Exchangeable storage medium for saving 
configuration data and enabling iFeatures
SCALANCE CLP 2GB W700 AP iFeatures

6GK5907-8UA00-0AA0

SCALANCE CLP 2GB W700 Client iFeatures 6GK5907-4UA00-0AA0

SCALANCE CLP 

3

2GB

6GK1900-0U

B4

0-0AA0

Summary of Contents for 6GK5748-1GY01-0AA0




























































































Reviews:

No comments