background image

24

SE 80/185 T - SE 100/185 T - SE 130/250T

      

1.0.1- 2008

Warranty statement

GB

1. The equipment manufactured by Sleipner Motor AS (The “Warrantor”) is warranted to be free from defects in workmanship and materials under normal 

 

  use and service.
2. This Warranty is in effect for of two years from the date of purchase by the user. Proof of purchase must be included, to establish that it is inside the 
  warranty period.

3. This Warranty is transferable and covers the product for the specified time period. 

4. In case any part of the equipment proves to be defective, other than those parts excluded in paragraph 5 below, the owner should do the following:
  (a)  Prepare a detailed written statement of the nature and circumstances of the defect, to the best of the Owner’s knowledge, including the date of  

      purchase, the place of purchase, the name and address of the installer, and the Purchaser’s name, address and telephone number;
  (b)  The Owner should return the defective part or unit along with the statement referenced in the preceding paragraph to the warrantor,  

      Sleipner Motor AS  

      or an authorized Service Centre, postage/shipping prepaid and at the expense of the Purchaser;
  (c)  If upon the Warrantor’s or Authorized Service Centre’s examination, the defect is determined to result from defective material or workmanship, the  

      equipment will be repaired or replaced at the Warrantor’s option without charge, and returned to the Purchaser at the Warrantor’s expense;
  (d)  no refund of the purchase price will be granted to the Purchaser, unless the Warrantor is unable to remedy the defect after having a reasonable 

      number of opportunities to do so. Prior to refund of the purchase price, Purchaser must submit a statement in writing from a professional boating  

      equipment supplier that the installation instructions of the Installation and Operation Manual have been complied with and that the defect remains;
  (e)  warranty service shall be performed only by the Warrantor, or an authorized Service Centre, and any attempt to remedy the defect by anyone else  

      shall render this warranty void.
5. There shall be no warranty for defects or damages caused by faulty installation or hook-up, abuse or misuse of the equipment including exposure to  

  excessive heat, salt or fresh water spray, or water immersion except for equipment specifically designed as waterproof. 

6. No other express warranty is hereby given and there are no warranties which extend beyond those described in section 4 above. This Warranty is 

  expressly in lieu of any other expressed or implied warranties, including any implied warranty of merchantability, fitness for the ordinary purposes for 

which  

  such goods are used, or fitness for a particular purpose, and any other obligations on the part of the Warrantor or its employees and representatives.
7. There shall be no responsibility or liability whatsoever on the part of the Warrantor or its employees and representatives for injury to any person or

 

  persons, or damage to property, loss of income or profit, or any other consequential or resulting damage or cost which may be claimed to have been 

 

  incurred through the use or sale of the equipment, including any possible failure or malfunction of the equipment, or part thereof.
8. The Warrantor assumes no liability for incidental or consequential damages of any kind including damages arising from collision with other vessels  

  or objects.
9. This warranty gives you specific legal rights, and you may also have other rights which vary from country to country.

Summary of Contents for SE 130/250T





























Reviews: