ShopBot PRSalpha Assembly Manual Download | Manualshive

Page: 55 / 100

background image

Section 5: Control Box Installation • May 2, 2016

© Copyright 2016 ShopBot Tools, Inc.

page 5-5

If installed, remove the hardware from the top hole where the lower
cross support is attached to the leg.

Slide the top brackets holding the control box toward the left until the
lower bracket touches the table leg.

Securely mount the lower control box bracket to the side of the leg
with bolt, flat washers, lock washer, and nut.

Once the lower bracket is firmly in place, tighten the button head
screws holding the upper brackets to the table sides.

Alternate Mounting for 12” and 24” Z-Axis
Models

12” and 24” Z-axis tools are configured with two
side plates on each side. The second side rail
requires a different lower mounting bracket. This
bracket will be installed over the lower cross sup-
port with the control box mounting tab pointing
down.

«
...
53
54
55
56
57
...
»

Summary of Contents for PRSalpha





































































































Reviews:

No comments

Related manuals for PRSalpha

Brand: ABB Pages: 52

Brand: NEC Pages: 146

Brand: Panasonic Pages: 45

Brand: Panasonic Pages: 3

Brand: C3 Custom Coolers Pages: 16

Brand: Daikin Pages: 2

Brand: Daikin Pages: 12

Brand: Daikin Pages: 12

Brand: Daikin Pages: 46

Brand: Daikin Pages: 21

Brand: Daikin Pages: 20

Brand: dbx Pages: 52

Brand: Hankscraft Runxin Pages: 58

Brand: GARAN Pages: 8

Brand: Gamma Vacuum Pages: 25

Brand: Gamma Pages: 28

Brand: Panasonic Pages: 8

Brand: I-Tork Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands