ShopBot PRSalpha Page 33 Assembly Manual Download | Manualshive

Page: 33 / 100

background image

Section 3: Gantry Installation • May 2, 2016

© Copyright 2016 ShopBot Tools, Inc.

page 3-3

Install Gantry

Caution:

The gantry is approximately 200

pounds and awkwardly weighted. Two peo-
ple should be used to lift the gantry.

Note:

Ensure front rails are already tightened.

With the help of another person, lift the gantry
onto the rails.

The dual V wheels should ride on each rail as shown.

Adjust the Rails

Align the back rail by running the gantry up and down the length of
the rail while watching from above to make sure rail is centered in the
wheel. Starting at one end of the gantry, adjust, then tighten the rail as
the gantry is slid down the length.

«
...
31
32
33
34
35
...
»

Summary of Contents for PRSalpha





































































































Reviews:

No comments

Related manuals for PRSalpha

Brand: Samson Pages: 48

Brand: Mako Networks Pages: 15

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 142

Brand: Panasonic Pages: 27

Brand: Panasonic Pages: 168

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 29

Brand: Panasonic Pages: 37

Brand: Panasonic Pages: 9

Brand: Kasco Pages: 3

C-NaviGator III

Brand: C-Nav Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands