manualshive.com logo in svg

ShopBot PRSalpha, Assembly Manual

Share
Download
ShopBot PRSalpha Assembly Manual Download Page 99

Section 12: Setup and Fine Tuning • May 2, 2016

© Copyright 2016 ShopBot Tools, Inc.  

 page 12-7

Fine Tune Setup

Square the Spindle

Move the spindle over the cutting surface. Use a square on the 
spindle side to adjust the spindle until it is perpendicular to the 
temporary work surface.

The spindle side is parallel with the spindle axis and is the most 
accurate measuring point for squaring with the tool deck.

Secure Mounting Screws

Tighten screws to hold spindle in proper alignment. Once the 
screws are snug, perform final tightening using sequence on left.

Check spindle square again after securing screws.

Test Movement Distance

Note: 

During this step, stay clear of the machine and be prepared to press the spacebar or emergen-

cy stop button if the machine travels further than expected.

Use the keypad controller to move the tool near the 0,0 location.

Mark the current position on the table with a pencil or pen.

Click on the zero axes button in the keypad control and check the boxes for the X- and Y-axes. The X 
and Y position values should change to 0.000 in the keypad and position windows.

Move the axis a set distance along the X-axis. In the keypad window click on the X value and change 
the value to 24 (1000 if in millimeters) then click the “Go to” button. The tool should move 24 inches 
(or 1000 mm) along the X-axis. If it doesn’t, go back to software setup and chose the correct default 
setting.

Move machine to 0,0 location. Verify jog by typing JX, 24 or JY, 24. Again, the tool should move 24 
inches (or 1000 mm) along the particular axis. If it doesn’t, go back to software setup and chose the 
correct default setting.

Summary of Contents for PRSalpha





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands