ShopBot PRSalpha Assembly Manual Download

Page: 14 / 100

Section 1: Setup and Assembly Overview • May 2, 2016

page 1-4

The

control box

is the “brain” of the machine and contains a control board, motor drivers, and other

electronic components that allow the tool to move with precision, accuracy, and power. It connects to
the PC through a single USB cable.

The

variable frequency device (VFD)

is used on machines that contain a spindle only (not a router).

It controls speed and power for the spindle. The control box provides the VFD with on/off signals, but
speed is controlled through an RPM controller unit, which connects to the PC through a separate USB
cable.

In most cases, the

X-, Y-, and Z-axes

will be referred to in respect to the machine. Another frequent-

ly-used term is the

XY home position

, as indicated here.

Summary of Contents for PRSalpha























































































Search results

Summary of Contents for PRSalpha

Reviews:

Related manuals for PRSalpha

Brands by name

Popular brands

ShopBot PRSalpha, Assembly Manual

Search results

Summary of Contents for PRSalpha

Reviews:

Related manuals for PRSalpha

Brands by name

Popular brands