ShopBot PRSalpha Assembly Manual Download | Manualshive

Page: 82 / 100

background image

Section 10: PRS Alpha Control Box Wiring • May 2, 2016

© Copyright 2016 ShopBot Tools, Inc.

page 10-2

Computer Recommendations

A PC running Windows XP/Vista/7/8 (Home Premium / Business, or higher) is required. The equivalent
of a dual core or higher, Pentium processor, and a minimum of 4GB RAM (8GB preferred) is recom-
mended.

A graphics display of 1024 x 768 will provide a good display, although a higher resolution may be pref-
erable.

Computer Configuration

Important: Some programs and features will interrupt the proper installation of ShopBot 3 control soft-
ware. To ensure trouble free installation and operation, ShopBot recommends performing the following
actions before installation.

_____ Install program using administrative account.

_____ Set User Account Control (UAC, not applicable to Windows XP) to “Never Notify.”

_____ Disable network connection.

_____ Disable security and antivirus software.

_____ Make sure the USB cable from the ShopBot is not plugged in.

Install ShopBot 3 Control Software and VCarve Pro Software

Refer to “Installing ShopBot Applications” section in “Uninstalling and Reinstalling ShopBot and
VCarve Software” document found at http://www.shopbottools.com/ShopBotDocs/files/SBG%20
00441%20Uninstalling%20and%20Reinstalling%20ShopBot%20and%20VCarve%20Software.pdf.

Software Overview

All programs included with the ShopBot are now installed. The icons below represent how they will
appear on the computer desktop.

«
...
80
81
82
83
84
...
»

Summary of Contents for PRSalpha





































































































Reviews:

No comments

Related manuals for PRSalpha

Brand: Panasonic Pages: 16

Brand: 1Control Pages: 8

Brand: C.Nord Pages: 100

CoreBuilder 9000

Brand: 3Com Pages: 78

REMOTE ACCESS SYSTEM 1500

Brand: 3Com Pages: 62

Brand: Daikin Pages: 5

Brand: National Instruments Pages: 9

Brand: National Instruments Pages: 14

Brand: National Instruments Pages: 11

Brand: Nauticam Pages: 2

Brand: National Instruments Pages: 18

Brand: National Instruments Pages: 10

Brand: National Instruments Pages: 20

GEMINI C Series

Brand: NAPCO Pages: 24

Brand: Paradox Pages: 2

Brand: Paradox Pages: 44

Brand: Samson Pages: 6

Brand: Waterway Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands