Sharp PC-AL Series Operation Manual Download Page 76 | Manualshive

Page: 76 / 159

background image

3-16

3

IEEE1394 Device

You can connect an IEEE1394 device to the computer. The IEEE1394 is a digital
interface for handling digital video, digital audio and other data in two directions
between the devices, and also controlling other equipments.

When two or more IEEE1394 compatible devices are connected to the computer in a
daisy chain, operations and data transactions are possible with not only the equipment
that is directly connected, but also other devices via the directly connected device.

•

Confirm the IEEE1394 device to be connected is Windows XP
compatible.

•

Use AC power for the computer and the IEEE1394 device especially
when reading/writing the data.

•

Some IEEE1394 devices require that you install the drivers before use.

Connecting IEEE1394 Device

•

You can connect the device with the computer powered on.

•

Be sure to read the manual(s) of the IEEE1394 device.

1.

Connect and end of the DV cable into the IEEE1394 port of the computer and the
other end into the DV connector of the IEEE1394 device.

IEEE1394 Port

DV Cable

To IEEE1394
Compliant Device

«
...
74
75
76
77
78
...
»

Summary of Contents for PC-AL Series
































































































































































Reviews:

No comments

Related manuals for PC-AL Series

Brand: Omen Pages: 15

Brand: IBM Pages: 6

R700-X.AP04A9 Entertainment Powerhouse

Brand: LG Pages: 1

Brand: LG Pages: 2

Brand: LG Pages: 78

S1 EXPRESS DUAL

Brand: LG Pages: 8

Brand: LG Pages: 2

Brand: LG Pages: 35

R700-X.AP03A9 Entertainment Powerhouse

Brand: LG Pages: 1

Brand: LG Pages: 27

Brand: LG Pages: 92

Brand: LG Pages: 87

Brand: LG Pages: 89

Brand: LG Pages: 100

Brand: LG Pages: 129

Brand: LG Pages: 129

Brand: LG Pages: 119

Brand: LG Pages: 128

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands