(5) Selection between the ON LINE mode
and the OFF LINE mode
In the ON LINE mode, the ON LINE lamp lights up to show that the
machine is ready for receiving print data from the host.
During copying, the machine is in the OFF line mode and the ON
LINE lamp goes off.
During printing, when copy interruption is made, printing is interrupted
and the ON LINE lamp blinks.
When a certain time passes after completion of copying, the machine
go back to the ON LINE mode and printing is resumed.
In any case, copying takes priority over printing.
The timing to going back to the ON LINE mode after completion of
copying can be set by the user program.
When the clear key is pressed twice, the machine goes into the ON
LINE mode immediately.
(6) Paper width detection and machine
operation
This machine is designed to detect only the following two sizes:
Max. paper size and Min. paper size shown in the table below.
Imaging (main scanning direction void area and image length) is per-
formed according to the paper size the machine detects, Therefore, if
the SIM 26-6 set value is not matched with the paper specification,
the image position on the paper is shifted to cause a trouble.
Destination code
Detectable paper size
Set value
Destination Paper type
Paper width
detector ON
(Max. paper size)
Paper width
detector OFF
(Min. paper size)
0
Inch series
11
×
8.5/14
×
8.5
8.5
×
5.5/8.5
×
5.5
1
EX Japan
AB series
A4 (210
×
356mm)
A5
2
Japan
AB series
A4 (210
×
356mm)
B5
(7) Auto copy function
The copy conditions can be set after turning on the power or during
resume operation from the energy save mode. Pressing the start key
allows copy reservation. After making a copy reservation, when the
copier warmup is completed, copy is started.
Once a copy reservation is made, the copy conditions cannot be
canceled unless the clear key is pressed.
(8) AE level adjustment procedure
The automatic exposure level can be adjusted to suit your copying
needs.This level is set for copying from the original table and copying
from the SPF respectively.
1) When adjusting the automatic exposure level for copying from the
SPF, place an original in the document feeder tray and make sure
that the SPF (
) indicator lights up.
When adjusting the level for copying from the original table, make
sure that no original is left in the document feeder tray.
2) Press the exposure mode selector key to select the photo (
)
mode.
3) Press and hold down the exposure mode selector key for ap-
proximately 5 seconds.
The photo (
) indicator will go out and the AUTO indicator
will begin to blink. One or two exposure indicators corresponding
to the automatic exposure level which has been selected will light
up.
4) Press the light (
) or dark (
) key to lighten or darken
the automatic exposure level as desired.
If exposure level 2 is selected, the two left-hand indicators will light
up simultaneously.
Also, if level 4 is selected, the two right-hand indicators will light up
simultaneously.
5) Press the exposure selector key. The AUTO indicator will stop
blinking and light up steadily.
NOTE: This automatic exposure level will remain in effect until you
change it again by this procedure.
(9) Toner save mode setup and cancel
Select MANUAL with the copy mode select key and press and hold
the key again for 5 sec. The mode display will change from MANUAL
to PHOTO blinking, and the currently set condition will be displayed in
the exposure level. Under this state, operate the density adjustment
key to set or cancel the toner save mode.
Press the left key: Level display "1" ON Toner save mode is set.
Press the write key: Level display "5" ON. Toner save mode is
canceled.
After adjustment, press the copy mode select key, and the mode
display will change from blinking to lighting. The setup is completed.
∗
The toner save mode is applicable to the auto and the manual
copy mode.
1) Press the copy mode select key to light the manual lamp.
1 3 5
AUTO
MANUAL
PHOTO
FO-3800M
6 – 3
