Sharp AR-FX11 Operation Manual Download Page 87

Page: 87 / 116

PROGRAMMING

Entering special characters

Special characters are entered with the Rapid key
overlay opened.

Press the [SP] key.

Select the special character that you
wish to enter with the [

][

]

keys.

To move to the next page, move the cursor to the
bottom line and press the [

] key. To move back to

the previous page, move the cursor to the top line and
press the [

] key. You can also change pages by

pressing the [

] key when the cursor is at the right

end of the bottom line, or the [

] key when the cursor

is at the left end of the top line.

Press the [OK] key.

The special character selected with the cursor is
entered and you return to the character entry screen.

If the Rapid key overlay is closed while a
special character is being selected, the
special character currently selected with the
cursor is entered.

XYZ

SPEED

SYMBOL

COMM. SETTING

SPACE/–

SPEC. CHARACTER

1/ 2

PQR

2-SIDED

COPY

SPECIAL FUNCTION

SPEC. CHARACTER

1/ 2

GHI

BACK

ENTER NAME

ABC

Note

Pegasus-E_Fax_Ex.book 85

ページ

２００４年１０月１８日　月曜日　午後８時４１分

Summary of Contents for AR-FX11





















































































































Search results

Summary of Contents for AR-FX11

Reviews:

Related manuals for AR-FX11

Brands by name

Popular brands

Sharp AR-FX11, Operation Manual

Search results

Summary of Contents for AR-FX11

Reviews:

Related manuals for AR-FX11

Brands by name

Popular brands