Sharp AR-FX11 Operation Manual Download Page 70

Page: 70 / 116

PROGRAMMING

[Editing and deleting auto-dial numbers]

To edit or delete an auto-dial number, follow steps 1 through
6 on pages 62 and 63 and then follow the steps below.

●

Editing a Rapid key or Speed Dial number

Select "RAPID/SPEED" with the [

] or

[

] key.

Press the [OK] key.

Select "CHANGE" with the [

] or [

]

key.

Press the [OK] key.

Press a Rapid key ([01] to [50]) or the
[SPEED] key.

• To edit a Rapid key, press the Rapid key that you

wish to edit ([01] to [50]).

• To edit a Speed Dial number, press the [SPEED] key

and then enter the Speed Dial number (000 to 299)
that you wish to edit with the numeric keys.

Edit the destination fax number with
the numeric keys.

Move the cursor to the digit(s) that you wish to edit with the [

] or

[

] key, and then enter the correct digit(s) with the numeric keys.

To delete a digit, move the cursor to the digit that you wish to
delete with the [

] or [

] key and then press the [C] key.

Press the [OK] key.

Edit the name of the destination (see
"ENTERING CHARACTERS" on page 82).

Press the [OK] key.

Edit the search characters (see
"ENTERING CHARACTERS" on page 82).

Characters added in step 8 will appear at the end of
the previously stored search characters. (Maximum of
10 characters altogether.)

A Rapid key or Speed Dial number cannot be
edited or cleared in the following cases:
• The Rapid key or Speed Dial number is

being used in a transmission in progress
or in a stored transmission.

• The Rapid key or Speed Dial number is

stored in a group key, program, or F-code
relay group.

Note

PQR

2-SIDED

COPY

SPECIAL FUNCTION

CHANGE/DELETE

RAPID/SPEED

GROUP

GHI

BACK

RAPID/SPEED

CHANGE

DELETE

XYZ

REDIAL/PAUSE

SPEED

SYMBOL

COMM. SETTING

SPACE/–

ABC

DEF

JKL

GHI

MNO

TUV

PQRS

WXYZ

@.-_

FUNCTION

ACC. #-C

READ-END

ENTER DIAL #
07
:

612345678

ENTER NAME
ABCDE

ABC

KEY WORDS

BCDE

[START]:ENTER

ABC

Pegasus-E_Fax_Ex.book 68

ページ

２００４年１０月１８日　月曜日　午後８時４１分

Summary of Contents for AR-FX11





















































































































Search results

Summary of Contents for AR-FX11

Reviews:

Related manuals for AR-FX11

Brands by name

Popular brands

Sharp AR-FX11, Operation Manual

Search results

Summary of Contents for AR-FX11

Reviews:

Related manuals for AR-FX11

Brands by name

Popular brands