Sharp AR-FX11 Operation Manual Download Page 14

Page: 14 / 116

ORIGINALS

ORIGINALS THAT CAN BE FAXED

Original sizes

* Long originals

Depending on the resolution setting and the width of the original, there may not be sufficient space in memory to
hold a long original. When a long original cannot be entirely scanned, select a lower resolution setting and/or
shorten the original.

Scanning area of original

When faxing an original, note that the edges of the
original cannot be scanned.

Width of edges that cannot be scanned:
5 mm from top and bottom edges, 6 mm (or less) from left
and right edges

Automatic reduction of faxed document

If the size (width) of the faxed document is greater than the receiving machine's paper size, the size will be
automatically reduced.

You can turn off automatic reduction. In this case, the left and right edges will not be transmitted. (See "AUTO
REDUCE TX" on page 100.)

Minimum original size

Maximum original size

Using the SPF

A5: 210 mm (width) x 148 mm (length)
(8-1/2" (width) x 5-1/2" (length))
A5R: 148 mm (width) x 210 mm (length)
(5-1/2" (width) x 8-1/2" (length))

297 mm (width) x 800 mm* (length)
(11" (width) x 31-1/2"* (length))
* Long documents can be

transmitted

Using the document glass

297 mm (width) x 432 mm (length)
(11" (width) x 17" (length))

• Originals that are not a standard size (A5, A4, A4R, B4, A3, 8-1/2" x 11", 8-1/2" x 11"R (5-1/2" x 8-1/2", 5-1/2"

x 8-1/2"R, 8-1/2" x 11", 8-1/2" x 11"R, 8-1/2" x 14", 11" x 17", A4, A4R if the machine uses inch-based paper
sizes)) can also be faxed.

• There are restrictions on originals that can be scanned using the SPF. For more information, see "NORMAL

COPYING" in the "Operation manual (for general information and copier)".

Faxed document width

Receiving machine's

paper width

Size after reduction

Ratio

A3 (11" x 17")

B4 (8-1/2" x 14")

1 : 0.78 (1 : 0.64)

A3 (11" x 17")

A4 (8-1/2" x 11")

A4R (8-1/2" x 11"R)

1 : 0.5 (1 : 0.5)

B4 (8-1/2" x 14")

A4 (8-1/2" x 11")

A4R (8-1/2" x 11"R)

1 : 0.64 (1 : 0.78)

Note

5 mm

Total of 6 mm or
less

Pegasus-E_Fax_Ex.book 12

ページ

２００４年１０月１８日　月曜日　午後８時４１分

Summary of Contents for AR-FX11





















































































































Search results

Summary of Contents for AR-FX11

Reviews:

Related manuals for AR-FX11

Brands by name

Popular brands

Sharp AR-FX11, Operation Manual

Search results

Summary of Contents for AR-FX11

Reviews:

Related manuals for AR-FX11

Brands by name

Popular brands