Sharp AR-FX11 Operation Manual Download Page 21 | Manualshive

Page: 21 / 116

background image

19

BASIC OPERATIONS

2

6

Press the [START] key (

).

• Scanning begins.
• If the line is free, the machine will dial the receiving

machine and begin transmission as soon as the first
page is scanned. (Quick online transmission: page
25)

• If there is a previously stored job or a job is in

progress, or if the line is being used, all pages of the
original are scanned into memory and stored as a
transmission job. (This is called memory
transmission: the destination is automatically called
and the document transmitted after previously stored
jobs are completed.)

If scanning is completed
normally, the following
screen is appears briefly
and then the display
returns to the base
screen.

6

Press the [START] key (

).

Scanning begins.

7

If you have another page to scan,
change pages and then press the
[START] key (

).

• Repeat this sequence until all pages have been

scanned.

• You can change the resolution and exposure

settings as needed for each page 15.

• If no action is taken for one minute (the [START] key

(

) is not pressed), scanning automatically ends

and the transmission job is stored. (This function can
be disabled in the key operator programs.)

8

After the last page is scanned, press
the [READ-END] key ( ).

Open the SPF and remove the original. When the
original is removed or any key operation is performed,
the display returns to the base screen. (The
destination is automatically called and the document
transmitted after any previously stored jobs are
completed.)

Using the SPF

WXYZ

@.-_

READ-END

READING XX%
No.001 P-XXX

MEMORY AUTO
CONT A4R
STANDARD

AUTO

READ END XX%
No.001 P-XXX

MEMORY AUTO
CONT A4R
STANDARD

AUTO

Using the document glass

WXYZ

@.-_

READ-END

READING XX%
No.001 P-XXX

MEMORY AUTO
CONT A4R
STANDARD

AUTO

[START]:CONTINUE

[#]:READ-END

MEMORY AUTO
CONT A4R
STANDARD

AUTO

@.-_

. #-C

READ-END

READ END XX%
No.001 P-XXX

MEMORY AUTO
CONT A4R
STANDARD

AUTO

•

To cancel transmission

To cancel transmission while "READING" appears or before the

key is pressed, press the [C] or [CA] key.

To cancel a transmission job that is already stored, press the [FAX STATUS] key and cancel the job as
explained on page 26.

• A job number (3 digits) appears in the display with "READ END" when memory transmission is performed. If

you make a note of this number after performing a broadcast transmission, you can use the number to check
the results of the transmission in the transaction report or activity report.

• If the power is turned off or a power failure occurs while an original is being scanned in the SPF, the machine

will stop and an original misfeed will occur. After power is restored, remove the original as explained in
"ORIGINAL MISFEED IN THE SPF" in the "Operation manual (for general information and copier)".

Note

Pegasus-E_Fax_Ex.book 19

ページ

２００４年１０月１８日　月曜日　午後８時４１分

«
...
19
20
21
22
23
...
»

Summary of Contents for AR-FX11





















































































































Reviews:

No comments

Related manuals for AR-FX11

Brand: Singer Pages: 8

Brand: Oki Pages: 32

Brand: Magnum Pages: 11

Brand: Singer Pages: 46

Galaxy Pro 2700-WX-HR

Brand: Edic Pages: 24

Brand: Nobles Pages: 3

4182i 100 Series

Brand: Minerva Boskovice Pages: 38

Brand: Ricoh Pages: 134

Brand: Kärcher Pages: 237

Brand: Sharp Pages: 2

Brand: Sharp Pages: 2

Brand: Sharp Pages: 26

Brand: Sharp Pages: 52

Brand: Sharp Pages: 69

Brand: Sharp Pages: 112

Brand: Sharp Pages: 57

Brand: Sharp Pages: 118

Brand: Sharp Pages: 118

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands