Sharp AR-FX11 Operation Manual Download Page 82

Page: 82 / 116

PROGRAMMING

[EDITING/DELETING F-CODE PUBLIC BOXES]

Select "CHANGE" or "DELETE" with
the [

] or [

] key.

Press the [OK] key.

• If you selected "CHANGE" in step 9, follow the steps

in "Editing an F-code public box" which follows.

• If you selected "DELETE" in step 9, follow the steps

in "Deleting an F-code public box" which follows.

●

Editing an F-code public box

Select the name of the F-code public
box that you wish to edit with the [

]

or [

] key.

If not all letters of the box name appear, press the

key to display all letters. Press the

key once again

to return to the original screen.

Press the [OK] key.

Edit the name of the F-code public box
(see "ENTERING CHARACTERS" on
page 82).

• See step 9 of "PROGRAMMING F-CODE PUBLIC

(POLLING MEMORY) BOXES" (page 77).

• If you do not wish to edit the name, go to the

next step.

Press the [OK] key.

Edit the sub-address and passcode
(maximum 20 digits) with the numeric
keys.

• See steps 3 to 6 on page 65.
• If you do not need to edit the sub-address and

passcode, press the [OK] key and go to the
next step.

Press the [OK] key and then press the
[BACK] key to exit.

●

Deleting an F-code public box

Select the name of the F-code public
box that you wish to delete with the [

]

or [

] keys.

If not all letters of the box name appear, press the

key to display all letters. Press the

key once again

to return to the original screen.

Press the [OK] key.

Select "DELETE" with the [

] or [

]

key.

Press the [OK] key.

You will return to step 11. If you
wish to delete another public box,
repeat steps 11 through 14. To
exit, press the [BACK] key.

PQR

2-SIDED

COPY

SPECIAL FUNCTION

S.A. MEM POLLING

CHANGE

DELETE

GHI

BACK

PQR

2-SIDED

COPY

SPECIAL FUNCTION

S.A. MEM POLLING

SBC CO.

— — — — — —
— — — — — —
[#]:LIST DETAIL

GHI

BACK

PQR

2-SIDED

COPY

SPECIAL FUNCTION

S.A. MEM POLLING

SBC CO.

— — — — — —
— — — — — —
[#]:LIST DETAIL

GHI

BACK

Pegasus-E_Fax_Ex.book 80

ページ

２００４年１０月１８日　月曜日　午後８時４１分

Summary of Contents for AR-FX11





















































































































Search results

Summary of Contents for AR-FX11

Reviews:

Related manuals for AR-FX11

Brands by name

Popular brands

Sharp AR-FX11, Operation Manual

Search results

Summary of Contents for AR-FX11

Reviews:

Related manuals for AR-FX11

Brands by name

Popular brands