Sharp AR-FX11 Operation Manual Download Page 76 | Manualshive

Page: 76 / 116

background image

74

PROGRAMMING, EDITING, AND
DELETING F-CODE MEMORY BOXES

The procedure for programming a box for F-code transmission is explained here. There are three types of F-code
boxes: F-code public boxes (page 77), F-code confidential boxes (page 75), and F-code relay group boxes (page
76). F-code boxes are programmed, edited, and deleted as explained below.

PROGRAMMING AN F-CODE MEMORY BOX

A box name, sub-address, passcode, and the appropriate functions are programmed in an F-code box.

1

In Fax mode, press the [SPECIAL
FUNCTION] key.

Begin the following procedure from the base screen of
Fax mode.

When the [SPECIAL
FUNCTION] key is pressed, the
function menu screen appears.
(To select fax mode, see step 1
on page 18.)

2

Select "ENTRY" with the [

] or [

]

key.

3

Press the [OK] key.

4

Select "SUB ADD SETTING" with the
[

] or [

] key.

5

Press the [OK] key.

6

Select "S.A. CONF. BOX", "S.A. RELAY
GRP", "S.A. MEM POLLING", or
"CHANGE/DELETE" with the [

] or [

] key.

• To program an F-code

confidential box, select
"S.A. CONF. BOX" and
press the [OK] key. Next,
follow the steps in
"PROGRAMMING AN
F-CODE CONFIDENTIAL
BOX" on page 75.

• To program an F-code

relay group (box), select
"S.A. RELAY GRP" and
press the [OK] key. Next,
follow the steps in
"PROGRAMMING AN
F-CODE RELAY
GROUP" on page 76.

• To program an F-code

public (polling memory)
box, select "S.A. MEM
POLLING" and press the
[OK] key. Next, follow the
steps in "PROGRAMMING
F-CODE PUBLIC
(POLLING MEMORY)
BOXES" on page 77.

• To edit or delete an F-code

confidential box, F-code
relay group, or F-code
public box, select
"CHANGE/DELETE" and
then press the [OK] key.
Next, follow the steps in
"EDITING AND DELETING
F-CODE MEMORY
BOXES" on page 77.

• When programming a new F-code box, a sub-address that is already programmed in another box cannot be

used. However, the passcode can be the same as a passcode used in another box.

• A passcode can be omitted.
• Up to 10 F-code boxes of each type can be programmed. If 10 F-code boxes of one type have already been

programmed, a warning message will appear and you will not be able to program a new box. Delete any
unused F-code boxes (page 77) and then program the new box.

Note

2-SIDED

COPY

SPECIAL FUNCTION

ACC.

DUPLEX SCAN

GH

PQR

2-SIDED

COPY

SPECIAL FUNCTION

SPECIAL FUNCTION
ORIGINAL STORE
PRINT

ENTRY

GHI

OK

BACK

ENTRY
DIAL
PROGRAM

SUB ADD SETTING

OK

SUB ADD SETTING

S.A. CONF. BOX

S.A. RELAY GRP
S.A. MEM POLLING
CHANGE/DELETE

SUB ADD SETTING
S.A. CONF. BOX

S.A. RELAY GRP

S.A. MEM POLLING
CHANGE/DELETE

SUB ADD SETTING
S.A. CONF. BOX
S.A. RELAY GRP

S.A. MEM POLLING

CHANGE/DELETE

SUB ADD SETTING
S.A. CONF. BOX
S.A. RELAY GRP
S.A. MEM POLLING

CHANGE/DELETE

Pegasus-E_Fax_Ex.book 74

ページ

２００４年１０月１８日　月曜日　午後８時４１分

«
...
74
75
76
77
78
...
»

Summary of Contents for AR-FX11





















































































































Reviews:

No comments

Related manuals for AR-FX11

Brand: Oki Pages: 80

Brand: Oki Pages: 26

Brand: Oki Pages: 184

Brand: Oki Pages: 176

Brand: Panasonic Pages: 88

Brand: R+M Suttner Pages: 2

Brand: Reliable Pages: 44

Brand: Singer Pages: 7

Brand: Janome Pages: 40

Brand: Tivax Pages: 6

Brand: AFXlight Pages: 20

Brand: Siruba Pages: 10

Brand: Singer Pages: 109

Brand: Fellowes Pages: 94

Brand: Bosch Pages: 36

Brand: Brother Pages: 66

Brand: Brother Pages: 56

Brand: Brother Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands