Sharp AR-FX11 Operation Manual Download Page 55

Page: 55 / 116

TRANSMISSION USING F-CODES

PROCEDURE FOR F-CODE POLLING

Make sure that a document has not been placed in the document feeder tray or on the document glass, and then
follow the steps below.

In Fax mode, press the [SPECIAL
FUNCTION] key.

When the [SPECIAL
FUNCTION] key is pressed, the
special function selection
screen appears.
(To select fax mode, see step 1
on page 18.)

Select "SENDING OPTIONS" with the
[

] or [

] key.

Press the [OK] key.

Select "SUB ADD POLLING" with the
[

] or [

] key.

Press the [OK] key.

Enter the fax number of the other
machine with the numeric keys, or
press a Rapid key, or dial a Speed Dial
number (a group key cannot be used).

To clear a mistake when
entering a number with the
numeric keys, press the [C] key
to clear one digit at a time.

A destination selected with a Rapid key or Speed Dial
number is indicated by an icon and a number. To clear
an entry, press the [C] key.

Press the [OK] key.

Enter the sub-address (up to 20 digits)
with the numeric keys.

• Characters that can be entered are numbers, "#",

and spaces. However, the initial character cannot be
a space.

• If you make a mistake, press the [C] key and re-enter

the correct digit(s).

• If you specified a Rapid key or Speed Dial number in

step 6 that has a sub-address programmed, the
sub-address will appear. Go to the next step without
entering a sub-address.

Press the [OK] key.

• You must know the sub-address (SEP) and passcode (PWD) of the other machine's F-code polling memory

box.

• Serial polling (selecting multiple fax machines to be polled using a group key, Rapid keys, and Speed Dial

numbers) is not possible when using F-code polling.

Note

2-SIDED

COPY

SPECIAL FUNCTION

ACC.

DUPLEX SCAN

PQR

2-SIDED

COPY

SPECIAL FUNCTION

SPECIAL FUNCTION
FAX PRINT HOLD
TIMER MODE

SENDING OPTIONS

GHI

BACK

SENDING OPTIONS
SERIAL POLLING
SUB ADDRESS TX

SUB ADD POLLING

WXYZ

Pegasus-E_Fax_Ex.book 53

ページ

２００４年１０月１８日　月曜日　午後８時４１分

Summary of Contents for AR-FX11





















































































































Search results

Summary of Contents for AR-FX11

Reviews:

Related manuals for AR-FX11

Brands by name

Popular brands

Sharp AR-FX11, Operation Manual

Search results

Summary of Contents for AR-FX11

Reviews:

Related manuals for AR-FX11

Brands by name

Popular brands