manualshive.com logo in svg

SEW-Eurodrive DHE21B, Manual, Page: 8 / 80

Share
Download
SEW-Eurodrive DHE21B Manual Download Page 8

8

Manual – Controllers DHE/DHF/DHR21B (standard) and DHE/DHF/DHR41B (advanced)

2

Other applicable documentation

Safety Notes

2

Safety Notes

2.1

Other applicable documentation

•

Read through this document carefully before you commence installation and startup
of the DH.21B/41B options.

The following publications and documents apply to the connected units:

•

Operating instructions for the units (such as for MOVIDRIVE

®

 B, MOVITRAC

®

 B,

MOVIAXIS

®

)

•

Only electrical specialists are allowed to perform installation and startup observing
the relevant accident prevention regulations and the operating instructions of the
connected units (such units are, for example, MOVIDRIVE

®

 MDX60B/61B,

MOVITRAC

®

 B, MOVIAXIS

®

).

•

For units with functional safety, also observe the corresponding manual "Functional
Safety" or "Safe Disconnection – Conditions".

•

You must adhere to the information in the documentation as a prerequisite to fault-
free operation and fulfillment of warranty claims.

2.2

Bus systems

The DH.21B and DH.41B options support various bus systems. A bus system makes it
possible to adapt frequency inverters to the particulars of the machinery within wide
limits. As with all bus systems, there is a danger of invisible, external (as far as the
inverter is concerned) modifications to the parameters which give rise to changes in the
unit behavior. This may result in unexpected, though not uncontrolled, system behavior.

2.3

Safety functions

MOVIDRIVE

®

 MDX60B/61B and MOVITRAC

®

 B inverters may not perform any safety

functions without higher-level safety systems. Use higher-level safety systems to ensure
protection of equipment and personnel. For safety applications, ensure that the informa-
tion in the following publications is observed: "Safe Disconnection for MOVIDRIVE

®

MDX60B/61B / MOVITRAC

®

 B".

2.4

Hoist applications

MOVIDRIVE

®

 MDX60B/61B, MOVITRAC

®

 B and MOVIAXIS

®

 must not be used as a

safety device in hoist applications.

Use monitoring systems or mechanical protection devices as safety equipment to avoid
possible damage to property or injury to people.

 

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Summary of Contents for DHE21B

















































































Reviews:

No comments