manualshive.com logo in svg

SEW-Eurodrive DHE21B, Manual, Page: 59 / 80

Share
Download
SEW-Eurodrive DHE21B Manual Download Page 59

Manual – Controllers DHE/DHF/DHR21B (standard) and DHE/DHF/DHR41B (advanced) 

59

5

Communication via Ethernet

Project Planning and Startup with MOVITOOLS

®

 MotionStudio

5.5.2

Address Editor

Overview

The Address Editor is a freeware tool by SEW-EURODRIVE GmbH & Co KG.

It is available once the "MOVITOOLS

®

MotionStudio" engineering software is installed.

However, it is used separately. 

You can use the Address Editor to establish a communication for your units via Ethernet
and to address the units. 

If you use a patch cable to connect the Ethernet interface of your engineering PC to the
Ethernet, the Address Editor detects all Ethernet stations in the connected network
segment (local network). 

Unlike with "MOVITOOLS

®

MotionStudio", you will 

not

 have to adjust the IP address of

the engineering PC to the local network.

This means the Address Editor is a useful addition to "MOVITOOLS

®

MotionStudio".

Proceed as follows if you have added other Ethernet stations to an existing network:

•

Start the Address Editor

•

Search for Ethernet stations

Once you have found the added Ethernet stations, you have two options:

•

Set (address) the detected Ethernet stations according to the network

•

Adjust (address) the engineering PC according to the network

Start the Address 
Editor

You can use the Address Editor once MOVITOOLS

®

 MotionStudio has been installed.

Do the following to start the Address Editor:

1. Close MOVITOOLS

®

 MotionStudio.

2. Start the Address Editor from the Windows start menu via:

[Start] / [Programs] / [SEW] / MOVITOOLS MotionStudio] / [Address Editor
(Address Tool)]

Searching for 
Ethernet stations

You can use the Address Editor to find Ethernet stations in a network. This is especially
useful for finding recently added Ethernet stations. The Address Editor also helps you
to locate the Ethernet interface of detected Ethernet stations.

Do the following to search for Ethernet stations and localize the hardware:

1. Select "Ethernet" as the interface for PC and unit. To do so, click on the

corresponding option field in the lower part of the window.

2. Click [Next] to confirm your selection and proceed to the next dialog.

INFORMATION

The Address Editor can only be used with the DHR21B/41B option (connection via
X30-1/-2).

0

0

I

 

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Summary of Contents for DHE21B

















































































Reviews:

No comments