SEW-Eurodrive DHE21B Manual Download Page 15

Page: 15 / 80

Manual – Controllers DHE/DHF/DHR21B (standard) and DHE/DHF/DHR41B (advanced)

Installation options of DH.21B/41B

Assembly and Installation Notes

4.1

Installation options of DH.21B/41B

Observe the following installation instructions:

4.2

Installing the DH.21B/41B option in MOVIDRIVE

MDX61B

•

You must insert the DHE21B/DHE41B option into the fieldbus slot of
MOVIDRIVE

MDX61B. If the fieldbus slot is not available, you can plug the

DHE21B/41B option into the expansion slot.

•

You must insert the DHF21B/DHR21B and DHF41B/DHR41B options into the expan-
sion slot of MOVIDRIVE

MDX61B. It cannot be installed in MOVIDRIVE

MDX61B

size 0.

4.2.1

Before you start

Read the following notes before installing or removing DH.21B/41B options:

•

Disconnect the inverter from power. Switch off the DC 24 V and the line voltage.

•

Before touching the DH.21B/41B option, take appropriate measures (discharge
strap, conductive shoes, etc.) to protect it from electrostatic charge.

•

Before installing

the DH.21B/41B option, remove the keypad and the front cover.

•

After installing

the DH.21B/41B option, replace the front cover and the keypad.

•

Keep the DH.21B/41B option in its original packaging until immediately before you
are ready to install it.

•

Hold the DH.21B/41B option only by its edges. Do not touch any of the components.

•

Never place the DH.21B/41B option on a conductive surface.

INFORMATION

•

You can insert the DH.21B/41B option in the MOVIDRIVE

MDX61B inverter. Do

not insert it in the MOVIDRIVE

MDX60B inverter.

•

Option cards can only be installed or removed for MOVIDRIVE

MDX61B sizes 1

to 6.

•

The installation or removal of option cards for MOVIDRIVE

MDX61B size 0

inverters must only be carried out by SEW-EURODRIVE engineers.

•

The installation or removal of the DH.21B/41B option in MOVIAXIS

as well as the

installation of the stand-alone housing DH.21B41B/UOH..B must only be carried
out by SEW-EURODRIVE engineers.

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Summary of Contents for DHE21B

















































































Search results

Summary of Contents for DHE21B

Reviews:

SEW-Eurodrive DHE21B, Manual, Page: 15 / 80

Search results

Summary of Contents for DHE21B

Reviews: